Cool water supply – Kenmore Coldspot 106 consumer handbook

Cool water supply – Kenmore Coldspot 106 consumer handbook

Posted by Sharon Smith | December 26, 2020 | compatible partners hookup apps

Cool water supply – Kenmore Coldspot 106 consumer handbook

Web Web Page 8

Read all guidelines carefully before you start. ESSENTIAL;

If running the ice box before setting up the water connection, turn ice manufacturer towards the OFF position to avoid procedure without water.

All installments must certanly be relative to neighborhood plumbing work

Utilize copper tubing and check always for leaks.

Install copper tubing only in places where conditions will continue to be above freezing.

If can take as much as twenty four hours for the ice manufacturer to start producing ice.

Tools needed;

in. open-end wrenches or two adjustable

Hand drill or electric drill (correctly grounded)

Your ice box dealer features a kit available with a

in. (6.35 mm) saddle-type shut-off valve, a union, and copper

tubing. Before buying, ensure a saddle-type valve

complies along with your regional plumbing work codes. Don’t use a piercingВ­

in. (4.76 mm) seat valve which reduces water movement

and clogs more easily.

Chilled water supply

The ice manufacturer water valve has a movement washer that will be utilized

as being a water force regulator. The ice manufacturer has to be attached to a water that is cold with water force between 30 and 120 psi. In cases where a issue happens, phone your energy company.

Linking to water line:

1. Disconnect disconnect or refrigerator energy.

Turn OFF main water supply. Start faucet that is nearest very very long

sufficient to clear type of water.

water pipeline close to the ice box.

Horizontal pipeline will continue to work, however the procedure that is following

should be followed: Drill from the side that is top of pipeline, perhaps perhaps not the base. This may help to keep water far from the drill. And also this keeps sediment that is normal gathering into the valve.

To look for the amount of copper tubing you shall need,

measure from connection on reduced remaining backside of fridge to

water pipeline. Add 7 ft. (2.1 m) to accommodate going ice box for cleansing. Utilize 14 in. (6.35 mm) O.D. (outside diameter)

copper tubing. Be certain both ends of copper tubing are cut square.

Employing a grounded compatible partners free trial drill, drill a 14 in. opening in the cool water pipeline

you’ve got chosen.

1. Chilled Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Off Valve

7. Packing Nut

Fasten shut-off valve to water that is cold with pipeline clamp. Be

certain socket end is sturdily into the 14 in. drilled opening into the water

pipeline and therefore washer is underneath the pipeline clamp. Tighten packing nut. Tighten the pipeline clamp screws very carefully and

evenly so washer makes a watertight seal. Don’t overtighten or you may crush the copper tubing, particularly when soft (coiled) copper tubing can be used. So Now you are prepared to link the copper tubing.

Slide compression nut on copper tubing as shown. Insert end of tubing into socket end squarely in terms of it shall get. Screw compression nut onto socket end with adjustable wrench. Try not to overtighten.

Spot the free end of this tubing into a container or sink, and

switch on main water supply and flush out tubing until water is obvious. Switch off shut-off valve from the water pipeline. Coil copper tubing.

Linking to fridge:

1. Connect the copper pipe into the valve inlet utilizing a compression

Sleeve and nut as shown. Fasten the compression nut. Try not to overtighten. Make use of the pipe clamp regarding the straight back associated with

fridge to secure the tubing to your refrigerator as shown. This can help alleviate problems with harm to the tubing once the ice box is pressed straight straight back from the wall. Proceed to step two.

2. Turn shut-off valve ON. look for leakages.

connections (including connections during the valve) or pea nuts that

Copper Tubing

3. Compression Nut

4. Valve Inlet

The ice maker comes with a integral water strainer. If

regional water conditions need regular cleansing or even a well is

your way to obtain water supply, a 2nd water strainer should

be set up within the

in. (6.35 mm) water line. Obtain a water

strainer from your own nearest appiiance dealer. Install at either pipe connection.

Add a comment

*Please complete all fields correctly

Newsletter Powered By : XYZScripts.com